Kai Shun Honing Steel

Shun honing steel is a process of fine-tuning the roughness and surface area texture of the steel by getting rid of the burrs and bumps from the surface area. If you are looking for the best items to fit your needs, then you ought to consider looking at this strategy. This method is best used in stainless steel tools and other metal tools that require to be honed and polished to get the right shine.


Table of Content

Click link below to go directly to the howto section of interest to you:

1.  Kai Shun Honing Steel

2.  Swiss Army Knife Hard To Open

3.  Cleaning Pocket Knife Rubbing Alcohol

4. Convex Sharpening System

5. How To Open A Can With A Can Opener

6. How To Restore An Old Pocket Knife


When you are looking for how to use Shun polishing steel, you require to make sure that you look at the processes utilized to refine and clean this type of tool. There are numerous ways in which the steel can be developed so you need to be sure that you are getting the best outcomes possible. This is kai shun honing steel.



Swiss Army Knife Hard To Open


If you own a Swiss army knife, you probably know how to utilize it and know how to tighten it too.

But did you know that you can in fact discover how to do both at the same time? That’s right, you can find out how to utilize your Swiss army knife in the right way and after that tighten it up the wrong way. And while this may seem difficult, it can be done.

The first thing you need to comprehend when discovering how to tighten up a Swiss army knife is that there are 2 different manages on the knife, and that they need to be loosened up in a different way.

The leading manage on the knife is what you are going to wish to use to loosen the clip or the pin, while the bottom manage will do the tightening. There specify ways to utilize each deal with for the job. This way you will know swiss army knife hard to open.


swiss army knife hard to open


To begin, get rid of the security or anti-slip grip from the blade. It comes off quickly in one smooth motion. Next, you will require to utilize the wire coat wall mount to put the blade into the little notch on the bottom of the handle.

Using a percentage of pressure, you will be able to spin the blade around and easily compress the deal with until it is seated into the notch. You will then be able to grip the deal with and wind the blade back in place, while loosening the other handle until it too.


Cleaning Pocket Knife Rubbing Alcohol


The primary reason that the Benchmade knives pall is that the quality of the material it’s made from is poor. You can clean your Benchmade knife so that it remains sharp for a longer time.

Some of the things you need to do to clean them are taking the blade out, wiping it with a wet fabric and using an option of water and mild meal cleaning agent.

Prior to you start cleaning it with a towel, you need to ensure that it is dry. If you don’t do this right, your knife will scratch and dull the blade.


Taking apart the pocketknife


When you have taken the blade out, you can clean it with a dry fabric by running it over the entire surface area and applying a solution of warm water and mild dish cleaning agent. Make sure that the blade is totally dry before re-applying the solution.

Repeat this process until the blade becomes blunt once again. When you are cleaning up benchmade knives, you require to run the blade across the whole surface and run it in one direction only, to avoid scratching or dulling the opposite.


cleaning pocket knife rubbing alcohol


Getting a rigid brush to clean


You can also utilize a stiff brush to clean your benchmade knife. You simply require to wet the brush with water and run it across the blade to eliminate any scratches or dirt. If there is a lot of dirt on the blade, it is best to file it initially and then use the blade brush to clean it. This will assist you keep your blade tidy for a longer amount of time.See also: cleaning pocket knife rubbing alcohol.


Convex Sharpening System


Are you trying to find methods on how to sharpen convex blade with a great outcome? For individuals who are simply beginning to discover the art of making blades, they frequently discover it rather tough especially if they have no concept about the things that they need to do.

For people who currently had actually made a lot of blades, they will not find it hard because they currently know how to hone it. But for those who are simply starting to learn more about sharpening and making blades, it is advised that you do some research initially before you really start doing it.


convex sharpening system 


One of the best things that you can do in order to acquire understanding about the important things that you need to do is reading books about sharpeners. The more details that you will be able to collect about sharpeners, the more understanding that you will likewise be able to gather about blade making in general.

This will help you understand all the important information about the stated tool that you will be using in the process of learning how to sharpen a convex blade.

You might also desire to take some tutorials from the Internet. There are a lot of websites available today that offer tutorials and suggestions on how you can learn to hone your blade.

This may assist you a lot in the process of finding out how to hone it given that you will have the ability to get a lot of ideas from them. These things are extremely vital in learning the essentials of this ability. Read more about: convex sharpening system.


how to sharpen convex blade



How To Open A Can With A Can Opener


How to open a can is a question asked by many people, and with great factor. There are numerous ways to open a bottle, however can openers are not among them. This short article is suggested to show how to open a can safely, so that you can take pleasure in the advantages of opening your own beverage instead of risking it.

According to lots of friends at, having is the best and most convenient approach to open a bottle without a can opener. Here is how to tackle it:

First, you need to use a butter knife or other non-sharp object to remove the labels from both ends of the can. Place one end of a sharp metal spoon over the label and slowly move it down the length of the label up until the second side of it gently presses versus the metal surface area of the can, launching the air caught within. You require to be very cautious when doing this, because the air inside might trigger a mess. Once you have released the air, twist the spoon counterclockwise, so that you wear not rip the paper beneath.


how to open a can with a can opener


Next, place the knife into the can with the air still trapped, and into the hole you just made. Do not force the air out – just slide it out carefully. Then, put the other side of the sharp spoon over the top of the hole you made, and slide it down gently. Again, do not require the air out. Twist the spoon counterclockwise to seal the hole.

Finally, eliminate the knife from the can by pulling it directly. You should have the ability to see the knife blade through the slot in the lid. This is the second approach for how to open a can utilizing nothing but your fingers. Continue doing this up until the bottle or jar is without air.

This is how to open a can using your bare hands. If you perform these actions properly, you should have no problem opening a can with your bare hands. The something to remember is that you must start at the top, pushing the can gradually down to the bottom, and then pulling it out again. The procedure needs to go without error for a minimum of 20 seconds.

Step 5 – Use the knife to pry the tab on the can open. Start by pushing the knife’s suggestion against the edge of the can, causing the plastic edge to bulge. Do not pull the knife out, because you will damage the edge. Continue spying, using brief sharp bursts, until the tab is pried loose. You might need to utilize 2 or three different points to reach the bottom half of the tab.

After the tab is pried loose, you will discover that the knife has now become a saw blade. Stop the sawing immediately, and turn the blade over to cut the contents of the can. Place the blade aside, and clean the blade with a piece of dry newspaper to soak up any remaining wetness.

With a tidy blade, you can continue with the process laid out above. This method works fantastic if you are trying to find out how to open a can without damaging your edge or knife. Read on for more about: how to open a can with a can opener.



how to open a can with a pocket knife



How To Restore An Old Pocket Knife


If you have owned a kitchen area cutlery for any length of time, then you will no doubt have actually come across the question of how to clean up a rusty knife.

While it is tempting to believe that rusted knives are safe to use, they can be extremely hazardous if you are not aware of how to properly clean them. If this is your very first time finding out how to clean a rusty knife, then it is recommended that you read this short post in its whole.

It will supply you with useful info on how to care for an old cutlery and keep it safe for many years to come.

The most important thing when discovering how to clean a rusted knife is to ensure that the knife is totally dry before you start dealing with it.

A lot of types of rust will form as a result of wetness permeating into the metal, which in turn triggers the rust to spread out. If there is moisture present in the piece, the metal might become soft and therefore more susceptible to rusting.

When cleaning the knife, always ensure that you do not use any protective gear, such as rubber gloves, welding gloves and even eye security, as these products can in fact cause damage to the metal instead of aid it.

Wearing any type of mask while cleaning up the rusted knife is strongly advised against, as it can trigger additional damage to the knife. When getting rid of any product from the knife, constantly tidy both sides with one part water and one part cleaning agent.


how to restore an old pocket knife


To begin the process of how to clean up a rustic knife, it is very important to identify whether the blade has actually been impacted by rust.

For blades made from carbon steel, merely utilize a dry cotton fabric to clean the rust away. If the blade is made of stainless-steel (also known as alloy blade) then use a moderate soap to clean the surface.

To eliminate discolorations and other kinds of discolorations, dab the rust with alcohol. Be sure to rinse well, otherwise the stain will leak back into the metal, damaging the metal and lowering the blade’s strength.

If the blade has been affected by rust, then scrape or rub the location with a knife to get rid of as much of the rust as possible. Attempt utilizing coarse or tough stones to make the scraping motion more reliable.


Clean away all traces of foreign matter


Clean away all traces of the rust, but make sure not to remove the actual rust spot. Instead, utilize a damp rag to dab at the rust till it is easily removed. If this does not remove the whole stain, then use more detergent to make sure that the stain is entirely gone before continuing to the next action. Wash the location thoroughly to get rid of any staying residue from the rust stain.

For knives that are not protected by a layer of protectant, then this step of how to clean a rusty knife is not needed. Nevertheless, if you wish to be sure that no stain stays on your blade, then make sure to use a thin layer of oil to prevent deterioration throughout the re-heating process. Oil not only secures the blade, but it also increases the knife’s cutting efficiency. Heat treatments will likewise guarantee that your knife blade is rust-free for many years.



how to clean an old pocket knife



Cleaning up a dull knife is one of the most discouraging things you’ll ever need to do, particularly if you’re not comfy dealing with heavy steel. There are several actions in how to clean a rusty knife. You do not even need to spend hours doing it due to the fact that with a couple of minutes of your time, you can extend the life of your blade by several times.

Follow these tips on how to clean up a rusty knife and you’re on your way to having a lovely, rust-free knife in no time. Enjoy more about: how to restore an old pocket knife.